[. . . ] PT-EP05L/06L Instruction Manual PT-EP05L/06L http://www. olympus. com/ Jp En Fr De Sp Cs Kr ©2011 Printed in China VR808501 Instruction Manual Mode d'emploi Bedienungsanleitung Manual de instrucciones Thank you for buying the Underwater Case PT-EP05L/06L (hereinafter Case). Please read this instruction manual carefully and use the product safely and correctly. Wrong usage may cause damage to the camera inside the Case due to water leakage, and repair may not be possible. Before use, perform an advance check as described in this manual. Introduction Unauthorized copying of this manual in part or in full, except for private use, is prohibited. [. . . ] Removal Remove the LCD hood from the rails above and below the LCD monitor window one after the other by widening the LCD hood. Rails Installation Removal Mounting and removing the body cap Install to fit the concave and convex parts of the body cap and lens port. Be sure to remove the body cap before shooting. En EN 9 Installing the diffuser 1 Attach the diffuser to the port adapter. Diffuser Port adapter 2 Attach the hand strap on the Case body. 3 Install the diffuser on the Case. En EN 10 2. Advance check of the Case Advance check before use This Case has been the subject of thorough quality control for the parts during the manufacturing process and thorough function inspections during the assembly. In addition, a water pressure test is performed with a water pressure tester for all products to confirm that the performance conforms to the specifications. However, depending on the carrying, storage conditions and the maintenance status, etc. , the waterproof function may be damaged. Before using, always perform the following advance checks. Advance check 1 Before loading the digital camera in the Case, immerse the empty Case to confirm that there is no water leakage. When it is difficult, water leakage can be checked by referring "Water leakage test" (P. · Forgetting to install the O-ring · Part of an O-ring or an entire O-ring is outside the specified groove. · O-ring damage, cracks, deterioration or deformation · Sand, fibers, hair or other foreign matter sticking to the O-ring, the O-ring groove or the O-ring contact surface. · Attached strap or silica gel getting caught when closing the Case. CAUTION: If the advance test should show water leakage with normal handling, stop using the Case and contact your dealer or an Olympus service station. En EN 11 3. Loading the digital camera Check the digital camera Check the digital camera before loading it in the Case. 1. Battery confirmation It is impossible to change the batteries when using the Case. Make sure that you have sufficient remaining battery capacity before use. 2. Check the remaining number of pictures Check that the image storage medium has enough room for the number of pictures you want to take. 3. Remove the strap, lens cap and filter from the digital camera. If the digital camera is loaded without removing the strap, lens cap and the Case cannot be sealed properly and water leakage may be caused. 4. Attach the zoom gear (optional) and the antireflective ring. Antireflective ring POSR-EP03 cannot be used. Zoom gear M. ZUIKO DIGITAL ED 14-42mm II M. ZUIKO DIGITAL ED 14-42mm II R PPZR-EP02 Antireflective ring POSR-EP05 (supplied) En EN 12 Open the Case 1 Slide and hold the slide lock towards the arrow direction (1) and turn the open/close dial clockwise (2). 2 Open the rear lid of the Case gently. 1 Slide lock 2 CAUTION: Do not apply too much force while turning the open/close dial. Doing so may damage the dial. Attach the flash to the camera and raise the light emitting part Attach the flash supplied with the camera. Make sure to raise the light emitting part. En EN 13 Insert the batteries for the light Open the battery lid. Insert 2 AAA batteries on the ribbon. Pay attention to the battery direction. Close the battery lid. En EN 14 Load the digital camera 1 Confirm that the digital camera is OFF. [. . . ] (Be careful not to damage the groove with the tip of the O-ring remover. ) 3 Lift the O-ring, pinch it with your fingertips and pull it out of the Case. Remove any sand, dirt, etc. After visually checking that dirt has been removed from the O-ring, check for attached sand and other foreign matter, as well as for damage and cracks by squeezing the entire circumference of the O-ring lightly with your fingertips. Remove attached foreign matter from the O-ring groove with a clean cloth or a cotton swab. Also remove any sand or dirt attached to any part of the Case that comes into contact with the O-ring. CAUTION: · When a sharp object is used to remove the O-ring or to clean the inside of the O-ring groove, the Case and the O-ring may be damaged and water leakage may be caused. [. . . ]